Electronics For Imaging Fiery X12 Guía de instalación

Fiery EX12/EX2000d CONFIGURATION GUIDE

x Contents Chapter 7: Administering the Fiery Administrator functions 7-1 Setting passwords 7-2Passwords from the Control Panel 7-3Passwords 7-4 Cle

44-46 Performing Setup from the Control PanelHalftone Angle Magenta0–360 [15]Specify the Magenta halftone screen angle. Choose the angle to correctly

44-47 Color Setup optionsColor Setup optionsColor Setup allows you to set defaults the Fiery uses to control color output. Mac OS and Windows users wh

44-48 Performing Setup from the Control PanelRendering StylePhotographic/Presentation/Abs. Colorimetric/Rel. Colorimetric [Presentation]The color rend

44-49 Color Setup optionsPaper SimulationOff/On [Off]Specify whether to render the white point of the source color space as visible color in the Outpu

44-50 Performing Setup from the Control PanelSpot Color Matching On/Off [On]With this option On, the Fiery uses an internal lookup table to print the

44-51 Administrative functions in the Setup menuThe printed Job Log lists accounting information about each job, including user name, document name, t

44-52 Performing Setup from the Control PanelFont ArchivingYou can back up and restore fonts to a ZIP disk. All fonts are backed up or restored; you c

55-1 Accessing SetupAfter you perform initial Setup (Server, Network, and Printer Setup) from the Control Panel, you can change most Setup options fro

55-2 Setting up the Fiery from a Windows ComputerLocal Fiery SetupYou can access Fiery Server Setup in any of the following ways:• Right-click the Fie

55-3 Accessing SetupRemote Fiery SetupYou can access remote Setup from Fiery WebSetup or Command WorkStation.TO ACCESS FIERY WEBSETUP1. Start your Int

xi About this manual This manual is intended for anyone who is responsible for integrating the Fiery EX12/EX2000d Color Server ™ into a business env

55-4 Setting up the Fiery from a Windows ComputerGeneral Setup optionsYou can specify Fiery system settings that affect all users, such as the name of

55-5 General Setup optionsNOTE: Do not use the device name (DC12 or DC2000) as the server name. If you have more than one Fiery, do not give them the

55-6 Setting up the Fiery from a Windows ComputerJob Log SetupAuto Print Job Log Every 55 Jobs—Specify whether the Fiery prints the Job Log after ever

55-7 Network SetupNetwork SetupNetwork Setup configures the Fiery to receive print jobs over the networks that are used at your site. If the Fiery is c

55-8 Setting up the Fiery from a Windows ComputerEthernet (Port Setup)Enable Ethernet—Select if the Fiery is to be connected to an Ethernet network.Tr

55-9 Network SetupProtocolsYou can change AppleTalk, IPX/SPX, and TCP/IP protocol settings for the Fiery. From remote Setup, you change these settings

55-10 Setting up the Fiery from a Windows ComputerUnlike remote Setup, local Setup does not provide separate settings for enabling and configuring a pr

55-11 Network SetupAppleTalkThe current AppleTalk zone is displayed.

55-12 Setting up the Fiery from a Windows ComputerIPX/SPX Use this option to specify IPX/SPX frame types.The Fiery supports the following Ethernet fra

55-13 Network SetupTCP/IPSpecify TCP/IP settings. The current settings for IP address, subnet mask, and default gateway address are displayed. For inf

xii Introduction About this manual This manual covers the following topics:•Basic configuration of the Fiery to support printing over AppleTalk, TCP/I

55-14 Setting up the Fiery from a Windows ComputerTo set the subnet mask, enter one of the following values:255.0.0.0 if the IP address starts with a

55-15 Network SetupServicesYou can configure the following network services:• LPD Printing (TCP/IP)—enable or disable LPD print services.•NetWare Print

55-16 Setting up the Fiery from a Windows ComputerLPD PrintingEnable LPD Print Services—Select to enable or disable LPD printing services.Enable Web S

55-17 Network SetupSetting up the Fiery for NDS printingOnly one NDS tree can be connected. To specify or change the NDS Tree, click Modify and specif

55-18 Setting up the Fiery from a Windows Computer2. In the NDS Connection window that appears, double-click an NDS tree in the list on the left.3. Na

55-19 Network Setup4. Select a Container from the containers list.5. Double-click a Print Server from the Select Print Server list.The full path to th

55-20 Setting up the Fiery from a Windows Computer6. Click OK.The Server Setup window appears, displaying the path to the selected Print Server on the

55-21 Network SetupTO SPECIFY THE NDS TREE SETTING FROM REMOTE FIERY SETUP1. Select Enable NDS and click Change Trees.2. In the NDS Configuration windo

55-22 Setting up the Fiery from a Windows Computer3. In the Select User Login window, select Use Default User Information or enter your password, and

55-23 Network Setup5. Select Use Default Print Queue Root or navigate to the Print Queue Root and click Finish.

1 1-1 Fiery on the network This chapter summarizes the stages in setting up the Fiery, and includes diagrams that refer you to other chapters or othe

55-24 Setting up the Fiery from a Windows Computer6. Click OK.The NDS Configuration window appears, displaying information about the Print Server.

55-25 Network SetupBindery SetupFrom the Network Setup tab, enable or disable Bindery services. The currently connected servers are displayed. A maxim

55-26 Setting up the Fiery from a Windows ComputerTO ADD BINDERY CONNECTIONS FROM LOCAL FIERY SETUP1. Click Modify in the Bindery Setup dialog box.The

55-27 Network Setup3. Select a print server from the Select Print Server list, and click Add.The name of the newly added server appears in the Connect

55-28 Setting up the Fiery from a Windows Computer4. When you finish adding servers, click OK.When you return to the Network Setup tab, the connected s

55-29 Network SetupTO REMOVE BINDERY CONNECTIONS FROM LOCAL FIERY SETUP1. Click Modify in the Bindery Setup dialog box.The Bindery Connections dialog

55-30 Setting up the Fiery from a Windows ComputerTO ADD BINDERY CONNECTIONS FROM REMOTE FIERY SETUP1. Select Enable PServer mode from the Service1 ta

55-31 Network Setup4. Select a print server from the list and click Finish.If necessary, enter the appropriate password in the Print Server Password d

55-32 Setting up the Fiery from a Windows ComputerTO REMOVE BINDERY CONNECTIONS FROM REMOTE FIERY SETUP1. Select Enable PServer mode from the Service1

55-33 Network SetupPoll Interval (local Setup) or PServer Poll Interval (remote Setup)Specify the polling interval (in seconds) for NetWare printing.

1 1-2 Connecting to the Network Stages of installation on the network Installation can be performed by a network or printing administrator. The stage

55-34 Setting up the Fiery from a Windows ComputerWindows Print Sharing (SMB)For setting up the Windows printing service, text fields may include upper

55-35 Network SetupEnable Windows Printing Service—Select to enable SMB (Server Message Block), the file and printer sharing protocol built into Window

55-36 Setting up the Fiery from a Windows ComputerHTTP Connection Support (WWW)Enable Web Services—Select to make the Fiery WebTools available to user

55-37 Network SetupPort 9100 printingEnable Port 9100—Enables applications to open a TCP/IP socket to the Fiery at Port 9100 to download a print job.

55-38 Setting up the Fiery from a Windows ComputerE-mail SetupE-mail Service Setup—Enabling Fiery e-mail services is required for all e-mail client se

55-39 Network SetupOutgoing Mail Server—Specify the IP address or server name that communicates the appropriate mail server and contact information to

55-40 Setting up the Fiery from a Windows ComputerPrinter Setup optionsYou can specify the following settings in the Printer Setup tab:•Printer Connec

55-41 Printer Setup optionsJob Batching DelayUse this option to specify the amount of time (in seconds) the server waits before batching jobs. This op

55-42 Setting up the Fiery from a Windows ComputerPS (PostScript) SetupThe options in the PS Setup menu in local Setup are located on the Paper Setup

55-43 Printer Setup optionsFiery EX12Color Mode—Specify whether to print color (CMYK) or Grayscale images to the Fiery by default. CMYK gives you full

11-3 Stages of installation on the networkSummary of Fiery network installationAt each computer from which users print to the Fiery:•Install the appro

55-44 Setting up the Fiery from a Windows ComputerDigital Press Mode—Specify the screen to use for your print job.Image Quality—Specify the type of pr

55-45 Printer Setup optionsPrint to PS Error—Specify whether the Fiery should print the available portion of a print job when it encounters a PostScri

55-46 Setting up the Fiery from a Windows ComputerColor SetupThe color job defaults can be overridden on a job-by-job basis.•A user can specify a diff

55-47 Printer Setup optionsFiery EX12RGB Source Profile (local Setup only)—Specify the RGB source space to be applied to RGB data. Rendering Style (loc

55-48 Setting up the Fiery from a Windows ComputerOutput Profile (local Setup only)—Specify the output profile to use for printing. Additional profiles c

55-49 Setting up printing groupsTO SET UP PRINTING GROUPS AND PASSWORDS1. Select Printing Groups from the Command WorkStation Server menu.2. Click Cre

55-50 Setting up the Fiery from a Windows ComputerExiting SetupWhen you have finished specifying Setup options, click OK and close the Setup dialog box

66-1 Configuring the Fiery and clients for Fiery WebToolsFiery WebTools allow you to manage your Fiery remotely from the Internet or from your company’

66-2 Configuring Fiery WebToolsTO ACCESS FIERY WEBTOOLS1. Start your Internet browser.2. Enter the IP address or DNS name of the Fiery.3. Press Enter.T

66-3 Setting the WebLink destinationSetting the WebLink destinationYou can change the pre-set WebLink destination; this function requires the Administ

11-4 Connecting to the NetworkQuick path to installationThe diagrams on the following pages show typical systems you can use to print and run Fiery so

77-1 Administrator functionsThis chapter provides tips on managing Fiery printing.Administrator functionsAdministration features are included with the

77-2 Administering the FierySetting passwordsYou can set or change the Administrator password for the Fiery. Anyone with the Administrator password ca

77-3 Setting passwordsPasswords from the Control PanelFor more information on Administrator access privileges, see page 3-3. For information on contro

77-4 Administering the FieryPasswordsYou can set, change, and remove passwords for the Fiery. These passwords, specific to the Server process, have dif

77-5 Clearing the FieryTO SET OR CHANGE A PASSWORD1. Select the password you want to change.2. Type the password in both the Enter New Password and Ve

77-6 Administering the FieryRestoring the Fiery to factory defaultsWhen Fiery system software is first installed, a backup copy is made automatically.

77-7 Managing Address BooksManaging Address BooksThe E-mail Service feature allows an administrator to import a list of e-mail addresses to the Fiery.

77-8 Administering the FieryThe administrator can manage the address books by sending an e-mail to the Fiery with command codes in the subject and mes

77-9 Printing a Configuration page from the Control PanelPrinting a Configuration page from the Control PanelThe Configuration page lists all the setting

11-5 Quick path to installationMac OS environment with AppleTalkKey to setup:1Mac OS computer User Software Installation Guide2Fiery Setup Chapter 4Ma

77-10 Administering the FieryMaintaining optimal Fiery performanceThe Fiery does not require maintenance. Beyond the obvious requirements of servicing

77-11 Starting and shutting down the FieryStarting and shutting down the FieryGenerally, you can leave the Fiery running all the time. This section de

77-12 Administering the FieryIf you press a button, the following options appear. Restarting the FieryUse the following procedure to restart the Fiery

77-13 Starting and shutting down the FieryShutting down the FieryYou may need to shut down the Fiery for service. When you do so, fonts downloaded to

AA-1 Token Ring Network OptionToken Ring is an alternative network architecture to the Ethernet architecture. Token Ring networks offer a high resista

AA-2 Token Ring Network OptionBack view of the Fiery with the Token Ring option installedTurn off the Fiery before connecting it to any network device

AA-3 Token Ring Network OptionIPX/SPX installationsIf your network uses IPX/SPX protocols with Token Ring, configure at least one printer, one Fiery Pr

BB-1 TroubleshootingThis chapter provides troubleshooting tips.Troubleshooting the FieryStartup diagnostics are described in the Installation and Serv

11-6 Connecting to the NetworkWindows computers in a Novell environmentIPX NetWare serverKey to setup:1NetWare server page 2-142Fiery Setup Chapter 43

BB-2 TroubleshootingFrame Type selection(Network Setup>Protocol Setup>IPX/SPX Setup)Invalid frame size. The network hub is not connected to a No

BB-3 TroubleshootingNavigating NDS tree(Network Setup>Service Setup>PServer Setup>NDS Setup)___ is empty. The chosen container contains no su

BB-4 TroubleshootingIn Network Setup, when you configure the IPX (Novell) connection, the Fiery queries the network for Novell file servers and trees, a

BB-5 TroubleshootingFor any Novell error, make sure:•Your IPX (Novell) network is connected to the Fiery.• The NetWare server you are trying to access

BB-6 Troubleshooting252Unable to log into server.Login does notexist.The server has connected to a file server, but is unable to log in to the server b

BB-7 TroubleshootingRuntime error messagesFor error messages related to canceling jobs and printing, including the Disk Full message and alerts to loa

BB-8 TroubleshootingSee the following table for the appropriate name.In this location For this item IPX/SPX networks TCP/IP networks SeeServer Setup

BB-9 TroubleshootingCannot connect to Fiery with Fiery utilitiesIf users cannot connect to the Fiery, check the following:•Fiery Setup—the appropriate

IndexNumerics100BaseT connector 1-1110BaseT 1-118-pin RJ-45 connector 1-11Aaccess level scenarios 3-6access to network and software 3-1accessing Setup

11-7 Quick path to installationWindows NT 4.0 Server environmentWindows computerWindows computerKey to setup:1 Windows NT 4.0 Server page 2-32Fiery Se

I-2 IndexCcables, Token Ring option A-2Cancel Jobfrom the Control Panel during printing 4-4from the Control Panel during RIPping 4-4canceling Setup ch

I-3 Indexcopier interface cable 3-10network cable 1-10to a Bindery file server 4-32, 4-33to multiple Bindery file servers 4-31Token Ring cable A-2contro

I-4 IndexEnable Printing Groups option 4-13Enable PServer option 4-26Enable Source Routing option 4-18, 5-8Enable TCP/IP for Ethernet option 4-20, 5-1

I-5 IndexFrom List option (adding a file server) 4-32Functions menu, Control Panel 4-5, 4-6Ggateway address, setting 4-21, 4-23General Setup options 5-

I-6 Indexjob management toolsdefined 3-1deleting jobs with 7-5printing Job Log 4-50Jobs Saved in Printed Queue option 4-13, 5-5LLCD 4-2line selection b

I-7 IndexIPX (Novell) 1-3, 1-4, 1-6lpd (TCP/IP) 1-3, 1-4, 1-9protocols supported 1-1using multiple protocols 1-4with Windows NT 1-7Network Setup 3-9ex

I-8 IndexPrint to PostScript Error option 4-44, 5-45Printed queue 3-2, 4-13printerconnection failure B-7not found B-7not in Chooser B-7Printer Agent,

I-9 Indexroot login 2-19routers 4-19Run Diagnostics commandfrom Control Panel 4-7Run Setup command 4-7Ssafety 4-2Save ChangesColor Setup, Control Pane

I-10 IndexTTCP/IPadding server to network 2-4Ethernet Setup from Control Panel 4-20host name B-7http protocol 1-1installing with Token Ring A-3lpd pri

I-11 IndexWebLink, see Fiery WebLinkWebSetup, see Fiery WebSetupWebSpooler, see Fiery WebSpoolerWebTools, see Fiery WebToolsWindows 9x/Meprinting in W

This manual is part of a set of Fiery ® documentation that includes the following manuals for users and system administrators:• The Quick Start Gui

11-8 Connecting to the NetworkWindows computers using Windows printing Windows computerWindows computerKey to setup:1 Windows computer User Software I

11-9 Quick path to installationUNIX workstations and Windows NT 4.0 computers on a TCP/IP networkKey to setup:1 UNIX server/host page 2-172Fiery Setup

11-10 Connecting to the NetworkConnecting network cable to the FieryIn this section, the back panel of the Fiery is illustrated, followed by informati

11-11 Connecting network cable to the FieryEthernet connectionFor Ethernet connections, the Fiery supports Unshielded Twisted Pair (UTP) cabling, defin

22-1 Fiery on a TCP/IP network with Windows NT 4.0This chapter describes environments that typically include one or more network servers—Novell NetWar

22-2 Setting up Network ServersTips for experts—Windows NT 4.0 with TCP/IPSetting up printing from Windows NT 4.0 using TCP/IP protocols is similar to

22-3 Fiery on a TCP/IP network with Windows NT 4.0Configuring a Windows NT 4.0 server to communicate with the FieryTo configure a Windows NT 4.0 server

22-4 Setting up Network ServersAdding the Fiery to the TCP/IP networkIf your TCP/IP network consists of Windows NT 4.0, Windows NT 4.0 clients, and Wi

22-5 Fiery on a TCP/IP network with Windows NT 4.0Installing the Fiery as a shared printerThe first step in creating a printer is installing the printe

Copyright © 2002 Electronics For Imaging, Inc. All rights reserved. This publication is protected by copyright, and all rights are reserved. No part

22-6 Setting up Network ServersConfiguring clients of a Windows NT 4.0 serverEach client of a Windows NT 4.0 server is already using a network protocol

22-7 Fiery on a TCP/IP network with Windows NT 4.0Configuring Windows computers without a Windows NT 4.0 serverIf your network does not have a Windows

22-8 Setting up Network ServersFiery on a NetWare 4.x or 5.x networkThe NetWise™ features built into the Fiery support the following network operating

22-9 Fiery on a NetWare 4.x or 5.x networkTips for experts—IPX networksSetting up the Fiery is similar to setting up any other PostScript printer on t

22-10 Setting up Network ServersYou do not need to rerun Setup when you add or remove a NetWare queue; however, you should restart the Fiery after you

22-11 Fiery on a NetWare 4.x or 5.x networkConfiguring an NDS connectionAbbreviations:FS = file serverPS = print serverPQ = print queue (on the NetWare

22-12 Setting up Network ServersSetting up an NDS connectionIn NDS, all NetWare entities (objects) are organized in a hierarchical tree structure. Obj

22-13 Fiery on a NetWare 4.x or 5.x networkSetting up a NetWare print queue for binderyFor NetWare 4.x in emulation mode, the NetWare print server and

22-14 Setting up Network ServersFiery on a NetWare 5.x network with NDPSThe Fiery supports printing over a NetWare 5.x network running either the TCP/

22-15 Fiery on a NetWare 5.x network with NDPSConfiguring a NetWare 5.x server for printingBefore you beginThe following procedure assumes NDPS has bee

FCC Information WARNING: FCC Regulations state that any unauthorized changes or modifications to this equipment not expressly approved by the manufact

22-16 Setting up Network ServersSetting up the Fiery on a NetWare 5.x networkDepending on the security needs at your organization, you can set up the

22-17 Fiery on a network with UNIX workstations9. For Printer Name, enter the name of the Fiery print connection you want users to print to, and click

22-18 Setting up Network ServersThe following information applies especially to the Fiery:• The Fiery is a printer controller that understands lpd pro

22-19 Fiery on a network with UNIX workstationsTO SET UP FIERY PRINTING ON UNIX SYSTEMS1. Specify the appropriate settings in Fiery Server Setup.To a

22-20 Setting up Network ServersTO PRINT TO THE FIERY• On a UNIX system running SunOS 4.x or other BSD-based variant, use the lpr command to send a jo

33-1 Levels of access and controlTo prepare for printing at your site, you must do some initial Fiery configuration, or Setup, to specify the network

33-2 Preparing for Fiery SetupIn addition, you can enable the Printed queue, which is a storage area for the most recent jobs from the Print queue. Th

33-3 Levels of access and controlPasswordsYou can implement passwords as a means of controlling access to Fiery functions. The Fiery allows you to set

33-4 Preparing for Fiery SetupFiery WebToolsThe Fiery can support Internet or intranet access with Fiery WebTools from Windows computers. To enable us

33-5 Levels of access and controlWebLinkWebLink provides all users with a link to an address on the Internet. To change the WebLink Internet address,

Proprietary Rights You acknowledge that the Software is proprietary to EFI and its suppliers and that title and other intellectual property rights th

33-6 Preparing for Fiery SetupControl level scenariosTypical scenarios of access and control, ranging from minimum control to maximum control, are des

33-7 Fiery system software5. An administrator and an operator; operator controls all jobs; no Fiery WebTool access (Maximum control) Only an administr

33-8 Preparing for Fiery SetupResident on the Windows NT Workstation is the following software unique to the Fiery:•Server—The Server is an independen

33-9 About SetupLocal Setup from the FieryYou can also perform Setup locally at the Fiery, using Server Setup, a Windows NT Control Panel. Some of the

33-10 Preparing for Fiery SetupYou must configure the Fiery with the correct Windows NT domain name. This is especially important for Windows printing

44-1 Fiery Setup from the Control PanelSetup is required the first time the Fiery is turned on after new system software is loaded. In this initial Set

44-2 Performing Setup from the Control Panel•Up and Down arrow buttons—scroll menus, options, and settings•Menu button—cancels without saving changes;

44-3 Fiery Control PanelActivity lightThe activity light indicates the current Fiery activity. If the light is:ButtonsSolid red An error has occurred,

44-4 Performing Setup from the Control PanelDisplay windowThe display window provides information about the status of the Fiery, displays menu informa

44-5 Fiery Control PanelInfo Status When the Fiery is not processing or printing a job, it displays information about the current server and software:

44-6 Performing Setup from the Control PanelFunctions menuThe Functions menu provides many of the options available from Command WorkStation. Choose t

44-7 Fiery Control PanelSuspend PrintingSuspend communication between the Fiery and the copier. You must suspend printing if you want to interrupt the

44-8 Performing Setup from the Control PanelAccessing Setup optionsTO ACCESS SETUP WHEN THE FIERY IS AT IDLE1. Make sure the information screen on the

44-9 Fiery Control PanelAbout the Control Panel Setup interfaceWhen you perform Setup from the Control Panel, you can select one menu after another an

44-10 Performing Setup from the Control PanelTypes of Setup screensThere are two types of Setup options:The following section provides three specific

44-11 Fiery Control PanelExample: Multiple choiceExample: Information entry with fieldsExample: Information entry with individual charactersPress the U

44-12 Performing Setup from the Control PanelNOTE: If you make a mistake during Setup, you can always use the Menu button to cancel without saving cha

44-13 Server Setup optionsSystem TimeEnter the correct system time. Enter the time based on the 24-hour clock in the form HH:MM (Hours:Minutes). The t

44-14 Performing Setup from the Control PanelClear Each Scan JobAfter 1 day/Now/Manually/After 1 week [After 1 day]Specify how you want to remove scan

44-15 Network Setup optionsThe available network types, and the Setup areas that pertain to them, are summarized in the following table. If the Token

Contents About the DocumentationIntroduction About this manual xii Chapter 1: Connecting to the Network Fiery on the network 1-1 Stages of installati

44-16 Performing Setup from the Control PanelTO ACCESS NETWORK SETUP OPTIONS1. Confirm that the network cable is connected to the Fiery.During Network

44-17 Network Setup optionsPort Setup optionsMaximum Frame Size(bytes)4202/2154/1130/632 [4202]Select the maximum frame size recommended by the networ

44-18 Performing Setup from the Control PanelEnable Source RoutingYes/No [No]Select Yes if your network supports source routing.Source RoutingRequest

44-19 Network Setup optionsAppleTalk ZoneList of zonesThe Fiery searches the network for AppleTalk zones in your network segment. Scroll through the l

44-20 Performing Setup from the Control PanelTCP/IP Setup with EthernetEnable Auto IP ConfigurationYes/No [Yes]Select Yes to allow the Fiery to obtain

44-21 Network Setup optionsGet Gateway Address AutomaticallyYes/No [Yes]Use this option to assign the gateway address automatically for printing with

44-22 Performing Setup from the Control PanelTCP/IP Setup with Token RingEnable TCP/IP for Token Ring, and enter the IP address and subnet mask. If yo

44-23 Network Setup optionsGet Gateway Address AutomaticallyYes/No [Yes]Use this option to get the gateway address automatically for printing with TCP

44-24 Performing Setup from the Control PanelIPX/SPX Setup options For protocols other than IPX/SPX, the frame type is automatically enabled and does

44-25 Network Setup optionsClear Frame TypesYou can clear all frame types at once by choosing Exit IPX/SPX Setup, then choosing IPX/SPX Setup and sele

viii Contents Chapter 3: Preparing for Fiery Setup Levels of access and control 3-1Fiery print connections 3-1Passwords 3-3Fiery WebTools 3-4Control

44-26 Performing Setup from the Control PanelService Setup optionsPServer is a Fiery program that can service the Novell print queues assigned to the

44-27 Network Setup optionsSelect NDS TreeList of treesUse the Up and Down arrow buttons to browse the list of NDS trees available to the Fiery. Choos

44-28 Performing Setup from the Control PanelIs user login neededto browse NDS tree?Yes/No [No]Select No if no password is required to browse the tree

44-29 Network Setup optionsEnter PasswordEnter the login password for the NDS tree, using the Up and Down arrow buttons to select characters, and the

44-30 Performing Setup from the Control PanelIf you select Entire NDS Tree, choosing OK returns to PServer Setup. Proceed with Bindery Setup (see page

44-31 Network Setup optionsBindery Setup optionsBindery Setup menuNOTE: If you change your mind about any of the menus you have selected, use the Menu

44-32 Performing Setup from the Control PanelOnce you have chosen a file server, the Fiery immediately tries to log in as a guest without a password.

44-33 Network Setup optionsFile Server Loginadministrator/supervisor/Enter Login Name [supervisor]This option appears only if a password is required f

44-34 Performing Setup from the Control PanelNetWare Print ServerList of print servers on selected file serverChoose the name of the print server you

44-35 Network Setup optionsEnter Your Print Server PasswordThis option appears only if your NetWare print server is password-protected. Enter your pri

ix Contents Color Setup options 4-47 Administrative functions in the Setup menu 4-50Job Log Setup 4-50Font Archiving 4-52Exit Setup 4-52 Chapter 5:

44-36 Performing Setup from the Control PanelPolling Interval optionsNetWare Server Poll Interval in Seconds 1–3600 [15]Specify the interval, in secon

44-37 Network Setup optionsUse Automatic ConfigurationYes/No [Yes]This option appears if you chose DHCP or BOOTP as the protocol for automatically obt

44-38 Performing Setup from the Control PanelWeb Services SetupIPP SetupSet Domain NameSelect from list/Enter manually [Select from list]This option p

44-39 Network Setup optionsPort 9100 SetupE-mail SetupEnable Print via E-mailYes/No [No]Choose Yes to enable printing through e-mail.Outgoing Server[1

44-40 Performing Setup from the Control PanelServer TypePOP3/IMAP [POP3]Choose the type of mail server.Fiery E-mail User NameEnter the user name of th

44-41 Network Setup optionsThe administrator authorizes a unique e-mail address to remotely administrate the Fiery e-mail services via e-mail. If an e

44-42 Performing Setup from the Control PanelPrinter Setup optionsPrinter Setup configures the connections and printing behavior associated with a part

44-43 PostScript Setup optionsJob Batching Delay0...99 [0]Use this option to specify the amount of time (in seconds) for the server to wait before bat

44-44 Performing Setup from the Control PanelConvert Paper SizesNo Letter/11x17->A4/A3 A4/A3->Letter/11x17 [No]Specify whether to convert pa

44-45 PostScript Setup optionsAllow Courier SubstitutionYes/No [Yes]Specify whether to substitute Courier for fonts that are unavailable when you down