Electronics For Imaging Fiery X12 Manual de servicio Pagina 27
- Pagina / 170
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
1
1-13 Connecting network cable to the Fiery
Ethernet connection
For connecting to Ethernet, the Fiery supports Unshielded Twisted Pair (UTP)
cabling, defined as Category 5 for use with 100BaseT; or as Category 3, Category 4, or
Category 5 for use with 10BaseT. The cable uses an 8-pin RJ-45 connector that plugs
into the RJ-45 socket on the Fiery.
NOTE: The 100BaseT type supported by the Fiery is 100BaseTX, also known as Fast
Ethernet. If an Ethernet hub is used, it must be a 100BaseTX hub. The term
“100BaseT” is used to refer to 100BaseTX.
TO CONNECT TO THE ETHERNET BOARD:
• Connect the network cable to the RJ-45 connector on the back of the Fiery.
A Category 5 unshielded twisted pair cable network cable must be used for 100BaseT.
Token Ring connection
For connecting to Token Ring, the Fiery supports Unshielded Twisted Pair (UTP)
cabling with an RJ-45 connector, and Shielded Twisted Pair (STP) with a DB-9
connector.
If the Token Ring option is installed, you can enable both Ethernet and Token Ring
simultaneously. Attach a cable to one of the Token Ring connectors, and attach a
second cable to one of the Ethernet connectors. For more information, see
Appendix A, “Token Ring Network Option.”
TO CONNECT TO THE TOKEN RING BOARD:
• Connect the network cable to the proper connector on the back of the Fiery.
- Fiery X12/XP12 1
- Contents 7
- Introduction 11
- About this manual 11
- About the documentation 12
- Fiery on the network 15
- Chapter 1: 15
- Connecting to 15
- 1-3 Fiery on the network 17
- SERVER CONFIGURATION 17
- CONNECTION 17
- CLIENT SETUP 17
- FIERY SETUP 17
- Quick path to installation 18
- 2 Fiery Setup Chapter 3 19
- Key to setup: 24
- Back view of the Fiery X12 25
- Back view of the Fiery XP12 26
- Ethernet connection 27
- Token Ring connection 27
- Levels of access and control 29
- Chapter 2: 29
- Preparing for 29
- Fiery Setup 29
- 2-2 Preparing for Fiery Setup 30
- Passwords 31
- Fiery WebTools 32
- Control level scenarios 34
- Fiery system software 36
- About Setup 36
- Local Setup from the Fiery 37
- About Fiery Setup 39
- Chapter 3: 39
- Accessing Setup options 41
- Types of Setup screens 43
- Server Setup options 45
- Network Setup options 47
- Port Setup options 49
- Network Setup 50
- Port Setup 50
- Protocol Setup options 51
- Exit TCP/IP Setup 52
- Ethernet Setup 52
- Token Ring Setup 52
- Parallel Port Setup 52
- TCP/IP Setup 52
- Exit Protocol Setup 57
- AppleTalk Setup 57
- IPX/SPX Setup 57
- Protocol Setup 57
- Service Setup options 59
- Yes/No [No] 60
- Enable NDS 60
- Enable PServer 60
- ..” to go up one level 61
- ..” to go up the 62
- “..” to go up one level 63
- Remove support for 68
- File server name 68
- Service Setup 69
- PServer Setup 69
- PostScript Setup options 74
- PCL Setup options 76
- O ACCESS PCL SETUP OPTIONS: 77
- Color Setup options 78
- Presentation 79
- Relative 79
- Colorimetric 79
- Job Log Setup 82
- Change Password 83
- Font Archiving 84
- 84
- Clearing the Fiery 85
- O RESTORE THE FIERY: 86
- 2. Choose Print Pages 87
- 3. Select Configuration 87
- 4-1 Accessing Setup 89
- Local Fiery Setup 90
- Remote Fiery Setup 91
- General Setup options 92
- O SET OR CHANGE A PASSWORD: 94
- O REMOVE A PASSWORD: 94
- Protocols 99
- AppleTalk 101
- 4-15 General Setup options 103
- Services 104
- 4-17 General Setup options 105
- 4-19 General Setup options 107
- 4-21 General Setup options 109
- 6. Click OK 109
- Bindery Setup 110
- TO ADD BINDERY CONNECTIONS: 111
- O REMOVE BINDERY CONNECTIONS: 113
- Poll Interval 114
- 4-27 General Setup options 115
- 4-29 General Setup options 117
- Printer Setup options 119
- PS (PostScript) Setup 120
- PCL Setup 122
- Color Setup 124
- Exiting Setup 125
- 2. Click Configuration 126
- 3. Click Print 126
- Support for Fiery utilities 127
- Chapter 5: 127
- Setting up 127
- Network Servers 127
- Tips for experts—IPX networks 129
- Configuring an NDS connection 131
- FS = file server 131
- PS = print server 131
- is published 138
- O ACCESS THE FIERY WEBTOOLS: 139
- O PRINT TO THE FIERY: 142
- Managing print jobs 143
- Administrator functions 145
- Chapter 6: 145
- Administering 145
- Troubleshooting the Fiery 148
- Novell error messages 152
- Runtime error messages 153
- Fiery Token Ring option 157
- Appendix A: 157
- Token Ring 157
- Network Option 157
- A-2 Token Ring Network Option 158
- A-3 Token Ring Network Option 159
- 1. Turn off the Fiery 159
- IPX/SPX installations 160
- TCP/IP installations 160
- Numerics 161
Relacionado con productos y manuales para Servidores Electronics For Imaging Fiery X12
(257 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.514 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales